![]() After receiving a signal, some devices enter in an analyzing and treating delay, and don't accept furthermore signal during this lapse of time." I think there is a delay added between 2 signals to different devices.Īll these can make a sequence very long, according to the various devices involved.īy experience, you can often reduce the inter key delay to 0ms, which decreases drastically the overall delay of a sequence. delay between devices: don't know where to configure this one, but Logitech is describing it as: "each IR signal is received and treated by each device, and ignored if not relevant to the device. Hi everybody Have discovered the Flirc and looking forward to getting it working with my XBMC and Logitech Harmony 1000 remote. input readyness: after changing the input canal of the device, time before send the next signal, usually 500ms Once you see it’s recognized, add the following to your configuration.yaml and restart: keyboardremote: - devicename: flirc Keyboard type: keydown. First, confirm it is recognized by Home Assistant by looking in the Supervisor’s Hardware tab. power-on readyness: after power-on signal, time before send the next signal, usually 1000 to 4000ms Now the Flirc can be set up in Home Assistant using the Keyboard Remote integration. repeat value: corresponds approximately to the "duration of each signal", value between 0 and 3 We recommend the FLIRC, though any generic USB receiver will probably work. inter key delay: the minimal time between 2 signals, usually 100ms. KEY_2 1 curl "volumio.Not sure how far you have gone in MyHarmony interface (yes, it's a nightmare probably designed by a maze architect for alien civilizations), you may know it all already, but there are a few parameters which may lead to the situation you are describing. ![]() For now i can control almost all of the shield remote buttons through the TV profile on the harmony remote thanks to HDMI CEC without the need for a flirc or anything else. KEY_1 1 curl "volumio.local:3000/api/v1/commands/?cmd=playplaylist&name=GDC-4" Id rather avoid upgrading the harmony since i dont want to have to charge the remote every couple days. #KEY_F2 2 /usr/local/bin/volumio pause & cd /data/plugins/user_interface & mv touch_display touch_display_off & volumio play KEY_MUTE 2 /usr/local/bin/volumio volume toggle KEY_VOLUMEUP 1 curl "volumio.local:3000/api/v1/commands/?cmd=volume&volume=plus" KEY_PLAYPAUSE 2 curl "volumio.local:3000/api/v1/commands/?cmd=toggle" KEY_RIGHT 1 /usr/local/bin/volumio seek plus KEY_LEFT 1 /usr/local/bin/volumio seek minus KEY_BACKSPACE 1 /usr/local/bin/volumio clear This post concerns an update of a previous post. Double Key Presses (with Harmony) Flirc isnt sending the correct function to my device. This guide can also be used with any other infrared remote. KEY_MUTE 1 /usr/local/bin/volumio volume toggle In this post the Logitech Harmony and Flirc are configured in such a way that they will work with both Android TV and Kodi. The remote communicates with the hub over RF (line of sight not necessary) and the hub outputs IR commands to the devices you are controlling (TV, audio receiver, FLIRC receiver, etc.) based on how you have the harmony activities programmed. I decided to give the X1 a try and had a pretty negative experience. As always, YMMV, this works for my Logitech Harmony Ultimate and a Flirc SE using Windows 7 64 bit. Certain Logitech profiles are built in to flirc. In my case I had to opt for two buttons for on/off and link the Logitech default 'power off' to Power on and the blue button to Power off. I am a long-time Harmony user, and have had a Harmony Elite for years. In the Harmony software, go to the Flirc device and change the power settings. KEY_REWIND 1 curl "volumio.local:3000/api/v1/commands/?cmd=prev" You need both FLIRC receiver and harmony hub. ago by jgranto SofaBaton X1 thoughts from a Harmony Elite owner Hi all, I wanted to share my experience with the SofaBaton X1. KEY_FASTFORWARD 1 curl "volumio.local:3000/api/v1/commands/?cmd=next" Almost everything can be done from the couch with the remote, not having to get the keyboard out is a big bonus to the WAF. ![]() ![]() Just walk through our super simple setup. I have my 650 set up very similarly and it works awesome. Flirc learns any remote control, not caring about different vendor protocols. KEY_PLAYPAUSE 1 curl "volumio.local:3000/api/v1/commands/?cmd=toggle" Warner306 from the forums put together this awesome guide for setting up a Logitech Harmony Remote for Windows. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |